AEM Infinity 710 Stand-Alone Programmable Engine Management System

AEM Infinity 710 Stand-Alone Programmable Engine Management System

2,753.95

INFINITY EMS TECHNICAL SPECS :

  • Up to 12 peak and hold injector drivers
  • Up to 12 (0-5V) ignition outputs
  • 3 analog temp inputs (Additional 3 with Advanced Tuning Package)
  • 11 analog voltage inputs (Additional 6 with Advanced Tuning Package)
  • 7 digital inputs (Additional 1 with Advanced Tuning Package)
  • 4 VR/Mag differential pair inputs (Additional 2 with Advanced Tuning Package)
  • 12 configurable outputs (Additional 1 with Advanced Tuning Package)
  • Variable cam control (up to 4 cams, application dependent)
  • Dual internal wideband controllers
  • 2 H-Bridge drivers for drive-by wire (Application dependent. Requires Advanced Tuning Package)
  • 32 Bit, 200MHz 400 MIPS primary microprocessor
  • 20 MHz auxiliary microprocessor
  • 6” L x 6” W x 2” H (1.125” H w/o connectors)
  • 24 Ounces/680.4 Grams
  • 129 pin, fully sealed ECU enclosure and IP67 spec connectors


INFINITY EMS FEATURES:

  • Compatible with most factory and performance aftermarket sensors
  • Includes start up configurations (supported applications only)
  • ECU set up wizard
  • User interface features 3D graphics
  • Internal simulator
  • USB 2.0 High-Speed communications
  • Tune using USB communication port (optional weatherproof extension cable sold separately)
  • High-speed USB data logging to mass storage device (4GB included, tested to 64GB)
  • Internal data logging playback mode on every channel, synchronized with all controls
  • AEMdata data analysis software included
  • 2-Channel CAN included
  • Runs on Windows-compatible software


INFINITY EMS CAPABILITIES:

  • Airflow model based calculations
  • Fuel control resolution to 1/10th of a microsecond (.0000001 sec)
  • Multi-fuel capable
  • Flex fuel compensated – fuel, ignition and boost with blend
  • Open-loop fuel pressure compensation
  • Ignition table, 20x20
  • VE airflow table, map vs. engine speed, 20x20
  • Configurable coil dwell (RPM, voltage and load based)
  • Individual cylinder ignition trim (RPM based)
  • Individual cylinder fuel trim (RPM based)
  • 3D ignition trim maps (coolant and air temp)
  • VE-based engine startup
  • Real-time sensor diagnostics
  • Integrated engine protection strategies
  • Dual internal wideband controllers
  • Target Lambda table, 10x10
  • User adjustable charge temperature blend (CLT/AIT, engine speed dependent)
  • O2 lean-out protection
  • Electronic boost control (time based or target based)
  • Idle control (stepper and pulsewidth)
  • Programmable traction control, 2-wheel speed or engine acceleration (4-wheel speed with Advanced Tuning Package)
  • 2-channel adaptive knock control
  • 2-step programmable launch control (3-step with Advanced Tuning Package)
  • No-lift shifting (Requires Advanced Tuning Package)
  • User configurable soft-cut rev limiters
  • User configurable anti-lag
  • Single stage wet or dry nitrous control coming soon (3-stage with Advanced Tuning Package, coming soon)


INFINITY EMS ADVANCED TUNING PACKAGE
Certain Advanced Tuning functions, hardware outputs and sensor inputs (see “Advanced Tuning Package” below) are available for the Infinity Programmable EMS. The Infinity EMS's Advanced Tuning Package is sold separately. For a limited time, the Infinity EMS Advanced tuning package is available at no additional charge.

Advanced Tuning Functions:

  • No-lift shift
  • 4-wheel speed traction control
  • 3-step launch control
  • Drive by wire (application dependent, coming soon)
  • 4-stage nitrous control (coming soon)

Advanced Tuning Hardware Outputs:

  • 1 high side driver
  • 2 H-bridge channels

Advanced Tuning Inputs:

  • 2 analog voltage inputs
  • 2 VR/Mag differential pair inputs
  • 1 digital/frequency input
  • 3 analog temp inputs
Add To Cart